[VoIP] Motorola VT1005 Rotary Dial Support

[Greg Blakely]

Yes, that can be done.

At this point, just email me the info, and I'll put it up.  

I could set up an upload directory so members could ftp up bits and
pieces of FAQs and configs.  Any thoughts on that?

 

> -----Original Message-----
> From: voip-bounces at ckts.info [mailto:voip-bounces at ckts.info] 
> On Behalf Of john jones
> Sent: Sunday, January 28, 2007 4:23 PM
> To: Voice Over IP Tandem for Analog Switches
> Subject: Re: [VoIP] Motorola VT1005 Rotary Dial Support
> 
> That is good news Doug.
> 
> When you get the dial plan stuff figured out, please let us know.
> 
> Is there a way to post the instructions and software needed 
> to set these up on ckts.info?  It would be good to establish 
> a repository for the various ATA's and for the Cisco 3810.  I 
> know of 3 or 4 people that have 3810's on the way.
> 
> 
> John
> 
> 
> --- Doug Alderdice <ka2wft at arrl.net> wrote:
> 
> > At 03:35 PM 1/28/2007 -0500, I wrote:
> > >Finally got my VT1005 talking to the Asterisk box
> > here (thanks to John
> > >Jones for a few helpful tips and moral support),
> > and preliminary rotary
> > >dial tests are downright dismal.
> > 
> > 
> > OK, things aren't quite as bad as I thought!!  It would 
> appear that it 
> > was a timeout setting issue in the configuration file for 
> the VT1005.  
> > The sample config file that John supplied on this list had 
> the dialing 
> > timeout settings pretty low for rotary dialing.  The values worked 
> > fine for DTMF, but when you have to wait for the dial to 
> spin back on 
> > higher digits, it became an issue.  I knew something had to 
> be wrong 
> > when I was getting the same errors with my Harris TS21 in 
> rotary dial 
> > mode!
> > 
> > The two settings I changed were:
> > 
> > BTIOPT TeleSipCritialDialTimeout[0]             =
> > 4000
> > BTIOPT TeleSipCritialDialTimeout[1]             =
> > 4000
> > BTIOPT TeleSipPartialDialTimeout[0]             =
> > 4000
> > BTIOPT TeleSipPartialDialTimeout[1]             =
> > 4000
> > 
> > Not sure what the difference is between the "critical" 
> timeout and the 
> > "partial" timeout, but all I know is I changed those values 
> to those 
> > shown above and I can now dial all over the CNET* with the 
> WE 500 w/#7 
> > dial and AE40 I initially attached to the VT1005.
> > 
> > *I can't dial our overseas members yet; still messing about 
> with the 
> > dial plan stuff in the VT1005 to make that work.  I think two 
> > different entries are "fighting" with each other since as soon as I 
> > dial the "01" of the "011" I get reorder from the 1005.
> > 
> > It's progress, though, and looking pretty good at the moment.
> > 
> > 
> > Doug.
> > 
> > 
> > _______________________________________________
> > VoIP mailing list
> > VoIP at ckts.info
> > http://lists.ckts.info/mailman/listinfo/voip
> > Project Web Page: http://www.ckts.info/
> > 
> 
> _______________________________________________
> VoIP mailing list
> VoIP at ckts.info
> http://lists.ckts.info/mailman/listinfo/voip
> Project Web Page: http://www.ckts.info/
> 
>