[VoIP] Cisco 3810

[Dennis D Hock]

Lee and others.  the person I purchased the 3810 from was Chris at West
tech recyclers out west.  He is at chrisk at westechrecyclers.com.  A short
summary of the unit shows it has 1 serial interface, I channelized T1/PRI
port, 256K non volatile config memory, 16384K bytes of processor board Sys
flash (AMD29F016), 1 2DSP High perfoprmance Compression Module (v01.A0, 2
serial (sync/async) network interface. It also has a combo Analog Voice
Module containign 4 FXS and 2 FXO.

These folks were very easy to do business with.  I purchased two units (
one for me, one for a fellow at work).  The only problem we had so far was
they seemed to have lost the order in their shipping dept.  It was however
very quickly made right when I hadn't received the units and inquired.  It
sounded like they had this package and had lost the address it was to be
sent to.  I would have no problem using them again.

At the time he had a selection of these and of course other units to choose
from.

Hope this helps all.

Dennis Hock

-----voip-bounces at ckts.info wrote: -----


To: Voice Over IP Tandem for Analog Switches <voip at ckts.info>,
jnovack at stromberg-carlson.org
From: john jones <jjones3601 at yahoo.com>
Sent by: voip-bounces at ckts.info
Date: 05/31/2007 07:39PM
Subject: Re: [VoIP] Cisco 3810

The FXO port supports DTMF, MF, and pulse dialing.

On one of my 3810's, ( I have routers like you guys have phones) has a FXO
port in slot 1/6.

To change the out-pulsing mode, use the following command

BatPhone(config-voiceport)#dial
BatPhone(config-voiceport)#dial-type ?
 dtmf   touch-tone dialer
 mf     mf-tone dialer
 pulse  pulse dialer



Just pick the one you want.

The E&M interface is exactly the same.

The FXS port supports DTMF and pulse dialing.  I've never tried MF on an
FXS port and I'm not going to try it now!

John


----- Original Message ----
From: Lee Spenadel <lee at spenadel.com>
To: jnovack at stromberg-carlson.org; Voice Over IP Tandem for Analog Switches
<voip at ckts.info>
Sent: Thursday, May 31, 2007 7:14:56 AM
Subject: Re: [VoIP] Cisco 3810

So was I.  How much was it?  I'm wondering if that would be a nice device
to
use for FXO in lieu of the Adtran given the outpulsing problem toward my
SxS.

L

-----Original Message-----
From: voip-bounces at ckts.info [mailto:voip-bounces at ckts.info] On Behalf Of
John Novack
Sent: Thursday, May 31, 2007 12:10 AM
To: Voice Over IP Tandem for Analog Switches
Subject: Re: [VoIP] Cisco 3810

I see Russ Price is awake this late to enjoy my Cisco!

JN


John Novack wrote:
> On a lighter note, with John Jones expert help, I have been working a
> little with the Cisco 3810
> Reloaded with SIP software, the box can be equipped with 6 ports, in any
> mix, of FXS, FXO or E&M circuits.
> Paul Wills is using one for his switch and ANI.
> I have mine on line right now set up for several foreign Ringback tones.
> Though it may not be available at all times, give it a call at 666-3101
> through 3104 for Cisco's electronic version of some other than North
> American precise tones. UK, RU, EG and JP
> No phones connected, so one can call at odd hours.
>
> John Novack
> _______________________________________________
> VoIP mailing list
> VoIP at ckts.info
> http://lists.ckts.info/mailman/listinfo/voip
> Project Web Page: http://www.ckts.info/
>
>
_______________________________________________
VoIP mailing list
VoIP at ckts.info
http://lists.ckts.info/mailman/listinfo/voip
Project Web Page: http://www.ckts.info/

_______________________________________________
VoIP mailing list
VoIP at ckts.info
http://lists.ckts.info/mailman/listinfo/voip
Project Web Page: http://www.ckts.info/



_______________________________________________
VoIP mailing list
VoIP at ckts.info
http://lists.ckts.info/mailman/listinfo/voipProject Web Page:
http://www.ckts.info/